本帖最后由 研究高科技 于 2012-11-17 15:51 编辑
请教高手：
我以前买一山寨平板，软件系统坏了，售后很差劲
刷了别的A10固件，触摸屏定义不同（左右互换等）
wifi 无效、TF卡打不开
请问如何通过DF来修改参数，让其适用与我的机器
http://l13.yunpan.cn/lk/sV2E6Giuh5Zr6
谢谢！
附网上找的固件包的参数：
;PAD application
;---------------------------------------------------------------------------------------------------------
; 说明： 脚本中的字符串区分大小写，用户可以修改"="后面的数值，但是不要修改前面的字符串
; 描述gpio的形式：Port:端口+组内序号<功能分配><内部电阻状态><驱动能力><输出电平状态>
;---------------------------------------------------------------------------------------------------------
[product]
version = "1.0"
machine = "A10-EVB-V1.2"
;----------------------------------------------------------------------------------
; system configuration
;----------------------------------------------------------------------------------
[target]
boot_clock =1008
dcdc2_vol =1400
dcdc3_vol =1250
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
[card_burn_para]
card_no = 0
card_line = 4
card_mode = 0
sdc_d1 = port:PF0<2><1><default><default>
sdc_d0 = port:PF1<2><1><default><default>
sdc_clk = port:PF2<2><1><default><default>
sdc_cmd = port:PF3<2><1><default><default>
sdc_d3 = port:PF4<2><1><default><default>
sdc_d2 = port:PF5<2><1><default><default>
[card_boot]
logical_start = 40960
sprite_gpio0 =
[card_boot0_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF0<2><1><default><default>
sdc_d0 = port:PF1<2><1><default><default>
sdc_clk = port:PF2<2><1><default><default>
sdc_cmd = port:PF3<2><1><default><default>
sdc_d3 = port:PF4<2><1><default><default>
sdc_d2 = port:PF5<2><1><default><default>
[card_boot2_para]
card_ctrl = 2
card_high_speed = 1
card_line = 4
sdc_cmd = port:PC6<3><1>
sdc_clk = port:PC7<3><1>
sdc_d0 = port:PC8<3><1>
sdc_d1 = port:PC9<3><1>
sdc_d2 = port:PC10<3><1>
sdc_d3 = port:PC11<3><1>
[twi_para]
twi_port = 0
twi_scl = port:PB0<2><default><default><default>
twi_sda = port:PB1<2><default><default><default>
[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PB22<2><1><default><default>
uart_debug_rx = port:PB23<2><1><default><default>
[uart_force_debug]
uart_debug_port = 0
uart_debug_tx =port:PF2<4>
uart_debug_rx =port:PF4<4>
[jtag_para]
jtag_enable =1
jtag_ms = port:PB14<3>
jtag_ck = port:PB15<3>
jtag_do = port:PB16<3>
jtag_di = port:PB17<3>
;*****************************************************************************
; sdram configuration
;
;*****************************************************************************
[dram_para]
dram_baseaddr = 0x40000000
dram_clk = 408
dram_type = 3
dram_rank_num =
dram_chip_density =
dram_io_width =
dram_bus_width =
dram_cas = 6
dram_zq = 0x7b
dram_odt_en = 0
dram_size =
dram_tpr0 = 0x30926692
dram_tpr1 = 0x1090
dram_tpr2 = 0x1a0c8
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_emr1 = 0x4
dram_emr2 = 0x0
dram_emr3 = 0x0
;*****************************************************************************
; mali configuration
;
; mali_clkdiv -- clock divisor for mali from pll4
;*****************************************************************************
[mali_para]
mali_used = 1
mali_clkdiv =3
[g2d_para]
g2d_used = 1
g2d_size = 0x1000000
;----------------------------------------------------------------------------------
; os life cycle para configuration
;----------------------------------------------------------------------------------
;----------------------------------------------------------------------------------
; Ethernet MAC configuration
;----------------------------------------------------------------------------------
[emac_para]
emac_used =0
emac_rxd3 = port:PA00<2><default><default><default>
emac_rxd2 = port:PA01<2><default><default><default>
emac_rxd1 = port:PA02<2><default><default><default>
emac_rxd0 = port:PA03<2><default><default><default>
emac_txd3 = port:PA04<2><default><default><default>
emac_txd2 = port:PA05<2><default><default><default>
emac_txd1 = port:PA06<2><default><default><default>
emac_txd0 = port:PA07<2><default><default><default>
emac_rxclk = port:PA08<2><default><default><default>
emac_rxerr = port:PA09<2><default><default><default>
emac_rxdV = port:PA10<2><default><default><default>
emac_mdc = port:PA11<2><default><default><default>
emac_mdio = port:PA12<2><default><default><default>
emac_txen = port:PA13<2><default><default><default>
emac_txclk = port:PA14<2><default><default><default>
emac_crs = port:PA15<2><default><default><default>
emac_col = port:PA16<2><default><default><default>
emac_reset = port:PA17<1><default><default><default>
;----------------------------------------------------------------------------------
;i2c configuration
;----------------------------------------------------------------------------------
[twi0_para]
twi0_used = 1
twi0_scl = port:PB0<2><default><default><default>
twi0_sda = port:PB1<2><default><default><default>
[twi1_para]
twi1_used = 1
twi1_scl = port:PB18<2><default><default><default>
twi1_sda = port:PB19<2><default><default><default>
[twi2_para]
twi2_used = 1
twi2_scl = port:PB20<2><default><default><default>
twi2_sda = port:PB21<2><default><default><default>
;----------------------------------------------------------------------------------
;uart configuration
;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function)
;----------------------------------------------------------------------------------
[uart_para0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PB22<2><1><default><default>
uart_rx = port:PB23<2><1><default><default>
[uart_para1]
uart_used = 0
uart_port = 1
uart_type = 8
uart_tx = port:PA10<4><1><default><default>
uart_rx = port:PA11<4><1><default><default>
uart_rts = port:PA12<4><1><default><default>
uart_cts = port:PA13<4><1><default><default>
uart_dtr = port:PA14<4><1><default><default>
uart_dsr = port:PA15<4><1><default><default>
uart_dcd = port:PA16<4><1><default><default>
uart_ring = port:PA17<4><1><default><default>
[uart_para2]
uart_used = 1
uart_port = 2
uart_type = 8
uart_tx = port:PI18<3><1><default><default>
uart_rx = port:PI19<3><1><default><default>
uart_rts = port:PI16<3><1><default><default>
uart_cts = port:PI17<3><1><default><default>
[uart_para3]
uart_used = 0
uart_port = 3
uart_type = 4
uart_tx = port:PH00<4><1><default><default>
uart_rx = port:PH01<4><1><default><default>
uart_rts = port:PH02<4><1><default><default>
uart_cts = port:PH03<4><1><default><default>
[uart_para4]
uart_used = 0
uart_port = 4
uart_type = 2
uart_tx = port:PH04<4><1><default><default>
uart_rx = port:PH05<4><1><default><default>
[uart_para5]
uart_used = 0
uart_port = 5
uart_type = 2
uart_tx = port:PH06<4><1><default><default>
uart_rx = port:PH07<4><1><default><default>
[uart_para6]
uart_used = 0
uart_port = 6
uart_type = 2
uart_tx = port:PA12<4><1><default><default>
uart_rx = port:PA13<4><1><default><default>
[uart_para7]
uart_used = 0
uart_port = 7
uart_type = 2
uart_tx = port:PA14<4><1><default><default>
uart_rx = port:PA15<4><1><default><default>
;----------------------------------------------------------------------------------
;spi configuration
;----------------------------------------------------------------------------------
[spi0_para]
spi_used = 0
spi_cs0 = port:PI10<3><default><default><default>
spi_cs1 = port:PI14<3><default><default><default>
spi_sclk = port:PI11<3><default><default><default>
spi_mosi = port:PI12<3><default><default><default>
spi_miso = port:PI13<3><default><default><default>
[spi1_para]
spi_used = 0
spi_cs0 = port:PA00<4><default><default><default>
spi_cs1 = port:PA04<4><default><default><default>
spi_sclk = port:PI01<4><default><default><default>
spi_mosi = port:PI02<4><default><default><default>
spi_miso = port:PI03<4><default><default><default>
[spi2_para]
spi_used = 0
spi_cs0 = port:PC19<3><default><default><default>
spi_cs1 =
spi_sclk = port:PC20<3><default><default><default>
spi_mosi = port:PC21<3><default><default><default>
spi_miso = port:PC22<3><default><default><default>
[spi3_para]
spi_used = 0
spi_cs0 = port:PA05<4><default><default><default>
spi_cs1 = port:PA09<4><default><default><default>
spi_sclk = port:PI06<4><default><default><default>
spi_mosi = port:PI07<4><default><default><default>
spi_miso = port:PI08<4><default><default><default>
;----------------------------------------------------------------------------------
;rtp_screen_size : 表屏幕尺寸，以斜对角方向长度为准，以寸为单位
;tp_regidity_level : 表屏幕的硬度，以指覆按压，抬起时开始计时，多少个10ms时间单位之后，硬件采集不到数据为准；
; 通常，我们建议的屏，5寸屏设为5,7寸屏设为7，
; 对于某些供应商提供的屏，硬度可能不合要求，需要适度调整
;rtp_press_threshold_enable: whether press threshold is enable or not. 0 is suggested.
;rtp_press_threshold : only when rtp_press_threshold_enable == 1, this para take effect.
; between 0 and 0xFFFFFF is supported.more bigger, more sensitive, 0x1f40 is suggested.
;rtp_sensitive_level : between 0 and 0xf is supported.more bigger, more sensitive, 0xf is suggested.
;rtp_exchange_x_y_flag : in some case, x, y need to be exchanged, at that situation, 1 is setted.
; normally, 0 is setted.
;----------------------------------------------------------------------------------
[rtp_para]
rtp_used =0
rtp_screen_size =7
rtp_regidity_level = 7
rtp_press_threshold_enable = 0
rtp_press_threshold = 0x1f40
rtp_sensitive_level = 0xf
rtp_exchange_x_y_flag = 0
;----------------------------------------------------------------------------------
;----------------------------------------------------------------------------------
;capacitor tp configuration
;external int function
;wakeup output function
;notice --- tp_int_port & tp_io_port use the same port
;name should be compatible with the corresponding ctp driver.
;at present, only "ft5x_ts"(0x38) and "Goodix-TS"(0x55) is supported.
;Rocky@20111016
;----------------------------------------------------------------------------------
[ctp_para]
ctp_used =1
ctp_twi_id = 2
ctp_name = "ft5x_ts"
ctp_twi_addr =0x38
;97F compibility TP
ctp1_used =1
ctp1_name ="Goodix-TS"
ctp1_twi_addr =0x55
ctp2_used =1
ctp2_name ="ssd253x-ts"
ctp2_twi_addr =0x48
ctp3_used =1
ctp3_name ="novatek-ts"
ctp3_twi_addr =0x09
ctp4_used =0
ctp4_name =
ctp4_twi_addr =
;gt82x.c
ctp7_used =1
ctp7_name ="gt82x"
ctp7_twi_addr =0x5d
cpt_screen_rotate = 0
ctp_screen_max_x = 800
ctp_screen_max_y = 480
;ctp_screen_max_x = 600
;ctp_screen_max_y = 800
;ctp_screen_max_x = 600
;ctp_screen_max_y = 1024
;ctp_screen_max_x = 768
;ctp_screen_max_y = 1024
ctp_revert_x_flag = 0
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0
;Rocky@20111102 indicate whether have key
ctp_havekey = 1
ctp_int_port = port:PH21<6><default>
ctp_wakeup = port:PB13<1><default><default><1>
ctp_io_port = port:PH21<0><default>
;----------------------------------------------------------------------------------
;touch key configuration
;at present, only "hv_keypad" is supported.
;----------------------------------------------------------------------------------
[tkey_para]
tkey_used =0
tkey_name = "hv_keypad"
tkey_twi_id = 2
tkey_twi_addr =0x62
tkey_int = port:PI13<6><default><default><default>
;----------------------------------------------------------------------------------
;motor configuration
;----------------------------------------------------------------------------------
[motor_para]
motor_used =1
motor_shake = port:PH23<1><default><default><0>
;----------------------------------------------------------------------------------
;nand flash configuration
;----------------------------------------------------------------------------------
[nand_para]
nand_used = 1
nand_we = port:PC00<2><default><default><default>
nand_ale = port:PC01<2><default><default><default>
nand_cle = port:PC02<2><default><default><default>
nand_ce1 = port:PC03<2><default><default><default>
nand_ce0 = port:PC04<2><default><default><default>
nand_nre = port:PC05<2><default><default><default>
nand_rb0 = port:PC06<2><default><default><default>
nand_rb1 = port:PC07<2><default><default><default>
nand_d0 = port:PC08<2><default><default><default>
nand_d1 = port:PC09<2><default><default><default>
nand_d2 = port:PC10<2><default><default><default>
nand_d3 = port:PC11<2><default><default><default>
nand_d4 = port:PC12<2><default><default><default>
nand_d5 = port:PC13<2><default><default><default>
nand_d6 = port:PC14<2><default><default><default>
nand_d7 = port:PC15<2><default><default><default>
nand_wp = port:PC16<2><default><default><default>
nand_ce2 = port:PC17<2><default><default><default>
nand_ce3 = port:PC18<2><default><default><default>
nand_ce4 =
nand_ce5 =
nand_ce6 =
nand_ce7 =
nand_spi = port:PC23<3><default><default><default>
nand_ndqs = port:PC24<2><default><default><default>
;----------------------------------------------------------------------------------
;disp init configuration
;
;disp_mode (0:screen0<screen0,fb0> 1:screen1<screen1,fb0> 2:two_diff_screen_diff_contents<screen0,screen1,fb0,fb1>
; 3:two_same_screen_diff_contets<screen0,screen1,fb0> 4:two_diff_screen_same_contents<screen0,screen1,fb0>)
;screenx_output_type (0:none; 1:lcd; 2:tv; 3:hdmi; 4:vga)
;screenx_output_mode (used for tv/hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50 5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60 11:pal 14:ntsc)
;screenx_output_mode (used for vga output, 0:1680*1050 1:1440*900 2:1360*768 3:1280*1024 4:1024*768 5:800*600 6:640*480 10:1920*1080 11:1280*720)
;fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444)
;fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA) --- 0 for linux, 2 for android
;----------------------------------------------------------------------------------
[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 1
screen0_output_mode = 4
screen1_output_type = 1
screen1_output_mode = 4
fb0_framebuffer_num = 2
fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb1_framebuffer_num = 2
fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0
lcd0_bright = 197
lcd1_bright = 197
lcd0_screen_bright = 50
lcd0_screen_contrast = 50
lcd0_screen_saturation = 57
lcd0_screen_hue = 50
lcd1_screen_bright = 50
lcd1_screen_contrast = 50
lcd1_screen_saturation = 57
lcd1_screen_hue = 50
;----------------------------------------------------------------------------------
;lcd0 configuration
;lcd_dclk_freq: in MHZ unit
;lcd_pwm_freq: in HZ unit
;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds
;lcd_hbp: hsync back porch
;lcd_ht: hsync total cycle
;lcd_vbp: vsync back porch
;lcd_vt: vysnc total cycle *2
;lcd_hv_if: 0:hv parallel 1:hv serial
;lcd_hv_smode: 0:RGB888 1:CCIR656
;lcd_hv_s888_if serial RGB format
;lcd_hv_syuv_if: serial YUV format
;lcd_hv_hspw: hsync plus width
;lcd_hv_vspw: vysnc plus width
;lcd_lvds_ch: 0:single channel; 1:dual channel
;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode
;lcd_lvds_bitwidth: 0:24bit; 1:18bit
;lcd_lvds_io_cross: 0:normal; 1:pn cross
;lcd_cpu_if: 0:18bit; 1:16bit mode0; 2:16bit mode1; 3:16bit mode2; 4:16bit mode3; 5:9bit; 6:8bit 256K; 7:8bit 65K
;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_gpio_0: SCL
;lcd_gpio_1 SDA
;----------------------------------------------------------------------------------
[lcd0_para]
lcd_used = 1
lcd_pwm_not_used = 0
lcd_pwm_ch = 0
lcd_pwm_freq = 10000
lcd_pwm_pol =1
;LCD Configure List ,please make the list like below
;Rocky@20111201
;RGB800x480 module name:H-B070D-15C
lcd_x =800
lcd_y =480
lcd_dclk_freq = 33
lcd_if = 0
lcd_hbp = 46
lcd_ht = 1055
lcd_vbp = 23
lcd_vt = 1050
;RGB 800x600 module name:H-B080D-24F
;lcd_x =800
;lcd_y =600
;lcd_dclk_freq = 40
;lcd_if = 0
;lcd_hbp = 46
;lcd_ht = 1056
;lcd_vbp = 23
;lcd_vt = 1270
;RGB 480x272 module name:KD43G18-40NB-A11
;lcd_x =480
;lcd_y =272
;lcd_dclk_freq = 9
;lcd_if = 0
;lcd_hbp = 2
;lcd_ht = 525
;lcd_vbp = 2
;lcd_vt = 572
;lvds 1024x600 module name:CLAP101NC01CW
;lcd_x =1024
;lcd_y =600
;lcd_dclk_freq = 52
;lcd_if = 3
;lcd_hbp = 33
;lcd_ht = 1344
;lcd_vbp = 23
;lcd_vt = 1270
;lvds 1024x768 module name :KD080D3-40NA-A2
;lcd_x =1024
;lcd_y =768
;lcd_dclk_freq = 65
;lcd_if = 3
;lcd_hbp = 160
;lcd_ht = 1344
;lcd_vbp = 23
;lcd_vt = 1612
;lvds 1024x768 module name : LG-LP097X02
;lcd_x =1024
;lcd_y =768
;lcd_dclk_freq = 100
;lcd_if = 3
;lcd_hbp = 480
;lcd_ht = 2084
;lcd_vbp = 6
;lcd_vt = 1600
;lcd_lvds_bitwidth = 1
;lcd_io_cfg0 = 0x04000000
;lcd_frm = 1
lcd_hv_if = 0
lcd_hv_smode = 0
lcd_hv_s888_if = 0
lcd_hv_syuv_if = 0
lcd_hv_vspw = 0
lcd_hv_hspw = 0
lcd_lvds_ch = 0
lcd_lvds_mode = 0
lcd_lvds_bitwidth = 0
lcd_lvds_io_cross = 0
lcd_cpu_if = 0
lcd_frm = 0
lcd_io_cfg0 = 0x10000000
lcd_gamma_correction_en = 0
lcd_gamma_tbl_0 = 0x00000000
lcd_gamma_tbl_1 = 0x00010101
;........
lcd_gamma_tbl_255 = 0x00ffffff
lcd_bl_en_used = 1
lcd_bl_en = port:PH07<1><0><default><1>
lcd_power_used = 1
lcd_power = port:PH08<1><0><default><1>
lcd_pwm_used = 1
lcd_pwm = port:PB02<2><0><default><default>
lcd_gpio_0 =
lcd_gpio_1 =
lcd_gpio_2 =
lcd_gpio_3 =
lcdd0 = port:PD00<2><0><default><default>
lcdd1 = port:PD01<2><0><default><default>
lcdd2 = port:PD02<2><0><default><default>
lcdd3 = port:PD03<2><0><default><default>
lcdd4 = port:PD04<2><0><default><default>
lcdd5 = port:PD05<2><0><default><default>
lcdd6 = port:PD06<2><0><default><default>
lcdd7 = port:PD07<2><0><default><default>
lcdd8 = port:PD08<2><0><default><default>
lcdd9 = port:PD09<2><0><default><default>
lcdd10 = port:PD10<2><0><default><default>
lcdd11 = port:PD11<2><0><default><default>
lcdd12 = port:PD12<2><0><default><default>
lcdd13 = port:PD13<2><0><default><default>
lcdd14 = port:PD14<2><0><default><default>
lcdd15 = port:PD15<2><0><default><default>
lcdd16 = port:PD16<2><0><default><default>
lcdd17 = port:PD17<2><0><default><default>
lcdd18 = port:PD18<2><0><default><default>
lcdd19 = port:PD19<2><0><default><default>
lcdd20 = port:PD20<2><0><default><default>
lcdd21 = port:PD21<2><0><default><default>
lcdd22 = port:PD22<2><0><default><default>
lcdd23 = port:PD23<2><0><default><default>
lcdclk = port:PD24<2><0><default><default>
lcdde = port:PD25<2><0><default><default>
lcdhsync = port:PD26<2><0><default><default>
lcdvsync = port:PD27<2><0><default><default>
;----------------------------------------------------------------------------------
;lcd1 configuration
;lcd_dclk_freq: in MHZ unit
;lcd_pwm_freq: in HZ unit
;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds
;lcd_hbp: hsync back porch
;lcd_ht: hsync total cycle
;lcd_vbp: vsync back porch
;lcd_vt: vysnc total cycle *2
;lcd_hv_if: 0:hv parallel 1:hv serial
;lcd_hv_smode: 0:RGB888 1:CCIR656
;lcd_hv_s888_if serial RGB format
;lcd_hv_syuv_if: serial YUV format
;lcd_hv_hspw: hsync plus width
;lcd_hv_vspw: vysnc plus width
;lcd_lvds_ch: 0:single channel; 1:dual channel
;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode
;lcd_lvds_bitwidth: 0:24bit; 1:18bit
;lcd_lvds_io_cross: 0:normal; 1:pn cross
;lcd_cpu_if: 0:18bit; 1:16bit mode0; 2:16bit mode1; 3:16bit mode2; 4:16bit mode3; 5:9bit; 6:8bit 256K; 7:8bit 65K
;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_gpio_0: SCL
;lcd_gpio_1 SDA
;----------------------------------------------------------------------------------
[lcd1_para]
lcd_used = 0
lcd_x = 0
lcd_y = 0
lcd_dclk_freq = 0
lcd_pwm_not_used = 0
lcd_pwm_ch = 1
lcd_pwm_freq = 0
lcd_pwm_pol = 0
lcd_if = 0
lcd_hbp = 0
lcd_ht = 0
lcd_vbp = 0
lcd_vt = 0
lcd_hv_if = 0
lcd_hv_smode = 0
lcd_hv_s888_if = 0
lcd_hv_syuv_if = 0
lcd_hv_vspw = 0
lcd_hv_hspw = 0
lcd_lvds_ch = 0
lcd_lvds_mode = 0
lcd_lvds_bitwidth = 0
lcd_lvds_io_cross = 0
lcd_cpu_if = 0
lcd_frm = 0
lcd_io_cfg0 = 0
lcd_gamma_correction_en = 0
lcd_gamma_tbl_0 = 0x00000000
lcd_gamma_tbl_1 = 0x00010101
;........
lcd_gamma_tbl_255 = 0x00ffffff
lcd_bl_en_used = 0
lcd_bl_en =
lcd_power_used = 0
lcd_power =
lcd_pwm_used = 1
lcd_pwm = port:PI03<2><0><default><default>
lcd_gpio_0 =
lcd_gpio_1 =
lcd_gpio_2 =
lcd_gpio_3 =
lcdd0 = port:PH00<2><0><default><default>
lcdd1 = port:PH01<2><0><default><default>
lcdd2 = port:PH02<2><0><default><default>
lcdd3 = port:PH03<2><0><default><default>
lcdd4 = port:PH04<2><0><default><default>
lcdd5 = port:PH05<2><0><default><default>
lcdd6 = port:PH06<2><0><default><default>
lcdd7 = port:PH07<2><0><default><default>
lcdd8 = port:PH08<2><0><default><default>
lcdd9 = port:PH09<2><0><default><default>
lcdd10 = port:PH10<2><0><default><default>
lcdd11 = port:PH11<2><0><default><default>
lcdd12 = port:PH12<2><0><default><default>
lcdd13 = port:PH13<2><0><default><default>
lcdd14 = port:PH14<2><0><default><default>
lcdd15 = port:PH15<2><0><default><default>
lcdd16 = port:PH16<2><0><default><default>
lcdd17 = port:PH17<2><0><default><default>
lcdd18 = port:PH18<2><0><default><default>
lcdd19 = port:PH19<2><0><default><default>
lcdd20 = port:PH20<2><0><default><default>
lcdd21 = port:PH21<2><0><default><default>
lcdd22 = port:PH22<2><0><default><default>
lcdd23 = port:PH23<2><0><default><default>
lcdclk = port:PH24<2><0><default><default>
lcdde = port:PH25<2><0><default><default>
lcdhsync = port:PH26<2><0><default><default>
lcdvsync = port:PH27<2><0><default><default>
;----------------------------------------------------------------------------------
;tv out dac configuration
;dacx_src: 0:composite; 1:luma; 2:chroma; 4:Y; 5:Pb; 6: Pr; 7:none
;----------------------------------------------------------------------------------
[tv_out_dac_para]
dac_used = 1
dac0_src = 4
dac1_src = 5
dac2_src = 6
dac3_src = 0
;--------------------------------------------------------------------------------
;csi gpio configuration
;csi_if: 0:hv_8bit 1:hv_16bit 2:hv_24bit 3:bt656 1ch 4:bt656 2ch 5:bt656 4ch
;csi_mode: 0:sample one csi to one buffer 1:sample two csi to one buffer
;csi_dev_qty: The quantity of devices linked to csi interface
;csi_vflip: flip in vertical direction 0:disable 1:enable
;csi_hflip: flip in horizontal direction 0:disable 1:enable
;csi_stby_mode: 0:not shut down power at standby 1:shut down power at standby
;csi_iovdd: camera module io power , pmu power supply
;csi_avdd: camera module analog power , pmu power supply
;csi_dvdd: camera module core power , pmu power supply
;pmu_ldo3: fill "axp20_pll"
;pmu_ldo4: fill "axp20_hdmi" "gc0308" 0x42
;fill "" when not using any pmu power supply
;csi_flash_pol: the active polority of the flash light IO 0:low active 1:high active
;--------------------------------------------------------------------------------
[csi0_para]
csi_used =1
csi_mode = 0
csi_dev_qty = 2
csi_stby_mode = 1
csi_mname = "gc0308"
csi_twi_id = 1
csi_twi_addr =0x42
csi_if = 0
csi_vflip = 0
csi_hflip = 0
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_flash_pol = 1
csi_mname_b = "gt2005"
csi_twi_id_b = 1
csi_twi_addr_b = 0x78
csi_if_b = 0
csi_vflip_b = 0
csi_hflip_b = 0
csi_iovdd_b = ""
csi_avdd_b = ""
csi_dvdd_b = ""
csi_flash_pol_b = 1
csi_pck = port:PE00<3><default><default><default>
csi_ck = port:PE01<3><default><default><default>
csi_hsync = port:PE02<3><default><default><default>
csi_vsync = port:PE03<3><default><default><default>
csi_d0 = port:PE04<3><default><default><default>
csi_d1 = port:PE05<3><default><default><default>
csi_d2 = port:PE06<3><default><default><default>
csi_d3 = port:PE07<3><default><default><default>
csi_d4 = port:PE08<3><default><default><default>
csi_d5 = port:PE09<3><default><default><default>
csi_d6 = port:PE10<3><default><default><default>
csi_d7 = port:PE11<3><default><default><default>
csi_d8 =
csi_d9 =
csi_d10 =
csi_d11 =
csi_d12 =
csi_d13 =
csi_d14 =
csi_d15 =
csi_reset = port:PH13<1><default><default><0>
csi_power_en = port:PH16<1><default><default><0>
csi_stby = port:PH18<1><default><default><0>
csi_flash =
csi_af_en =
csi_reset_b = port:PH13<1><default><default><0>
csi_power_en_b = port:PH16<1><default><default><0>
csi_stby_b = port:PH19<1><default><default><0>
csi_flash_b =
csi_af_en_b =
[csi1_para]
csi_used =0
csi_mode = 0
csi_dev_qty = 1
csi_stby_mode = 1
csi_mname = ""
csi_twi_id = 1
csi_twi_addr =0xba
csi_if = 0
csi_vflip = 0
csi_hflip = 0
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_flash_pol = 1
csi_mname_b = ""
csi_twi_id_b = 1
csi_twi_addr_b = 0x78
csi_if_b = 0
csi_vflip_b = 1
csi_hflip_b = 0
csi_iovdd_b = ""
csi_avdd_b = ""
csi_dvdd_b = ""
csi_flash_pol_b = 1
csi_pck = port:PG00<3><default><default><default>
csi_ck = port:PG01<3><default><default><default>
csi_hsync = port:PG02<3><default><default><default>
csi_vsync = port:PG03<3><default><default><default>
csi_field =
csi_d0 = port:PG04<3><default><default><default>
csi_d1 = port:PG05<3><default><default><default>
csi_d2 = port:PG06<3><default><default><default>
csi_d3 = port:PG07<3><default><default><default>
csi_d4 = port:PG08<3><default><default><default>
csi_d5 = port:PG09<3><default><default><default>
csi_d6 = port:PG10<3><default><default><default>
csi_d7 = port:PG11<3><default><default><default>
csi_d8 =
csi_d9 =
csi_d10 =
csi_d11 =
csi_d12 =
csi_d13 =
csi_d14 =
csi_d15 =
csi_d16 =
csi_d17 =
csi_d18 =
csi_d19 =
csi_d20 =
csi_d21 =
csi_d22 =
csi_d23 =
csi_reset = port:PH14<1><default><default><0>
csi_power_en =
csi_stby = port:PH17<1><default><default><0>
csi_flash =
csi_af_en =
csi_reset_b =
csi_power_en_b =
csi_stby_b =
csi_flash_b =
csi_af_en_b =
;--------------------------------------------------------------------------------
;tv configuration
;
;--------------------------------------------------------------------------------
[tvout_para]
tvout_used = 1
tvout_channel_num = 1
tv_en = port:PI12<1><default><default><0>
[tvin_para]
tvin_used = 0
tvin_channel_num = 4
;--------------------------------------------------------------------------------
;sata configuration
;
;--------------------------------------------------------------------------------
[sata_para]
sata_used = 1
sata_power_en =
;--------------------------------------------------------------------------------
; SDMMC PINS MAPPING |
; ------------------------------------------------------------------------------|
; 配置选项： |
; sdc_used --- 此sdc控制器是否使用，1-使用，0-不使用 |
; sdc_detmode --- 卡检测模式 |
; 1-gpio检测，2-data3检测，3-无检测，卡常在(不卡拔插) |
; 4 - manual mode(from proc file system node) |
; sdc_bwid --- 卡数据位宽，1-1bit， 4-4bit， other-no use |
; 其余: port配置 |
; ------------------------------------------------------------------------------|
; 特别说明： |
; 1.每个卡控制器必须有sdc_used配置，当sdc_used 为 0时，其余参数可不配 |
; 2.卡使用data3检测的时候(sdc_detmode 为 2)，gpio配置里SDC_D3的pull up/down需要|
; 保证高阻状态且外部电路需要对data3使用1MΩ左右的电阻下拉，使用请详细咨询，误擅|
; 自决定 |
; 3.使用gpio检测时必须配置sdc_det检测pin脚端口 |
;--------------------------------------------------------------------------------
[mmc0_para]
sdc_used = 1
sdc_detmode = 1
bus_width = 4
sdc_d1 = port:PF0<2><1><2><default>
sdc_d0 = port:PF1<2><1><2><default>
sdc_clk = port:PF2<2><1><2><default>
sdc_cmd = port:PF3<2><1><2><default>
sdc_d3 = port:PF4<2><1><2><default>
sdc_d2 = port:PF5<2><1><2><default>
sdc_det = port:PH20<0><1><default><default>
sdc_use_wp = 0
sdc_wp =
[mmc1_para]
sdc_used = 1
sdc_detmode = 1
bus_width = 4
sdc_cmd = port:PH22<5><1><2><default>
sdc_clk = port:PH23<5><1><2><default>
sdc_d0 = port:PH24<5><1><2><default>
sdc_d1 = port:PH25<5><1><2><default>
sdc_d2 = port:PH26<5><1><2><default>
sdc_d3 = port:PH27<5><1><2><default>
sdc_det = port:PH2<0><1><default><default>
sdc_use_wp = 0
sdc_wp =
[mmc2_para]
sdc_used = 0
[mmc3_para]
sdc_used = 1
sdc_detmode = 4
bus_width = 4
sdc_cmd = port:PI04<2><1><2><default>
sdc_clk = port:PI05<2><1><2><default>
sdc_d0 = port:PI06<2><1><2><default>
sdc_d1 = port:PI07<2><1><2><default>
sdc_d2 = port:PI08<2><1><2><default>
sdc_d3 = port:PI09<2><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
; ------------------------------------------------------------------------------|
; memory stick configuration
;--------------------------------------------------------------------------------
[ms_para]
ms_used = 0
ms_bs = port:PH06<5><default><default><default>
ms_clk = port:PH07<5><default><default><default>
ms_d0 = port:PH08<5><default><default><default>
ms_d1 = port:PH09<5><default><default><default>
ms_d2 = port:PH10<5><default><default><default>
ms_d3 = port:PH11<5><default><default><default>
ms_det =
; ------------------------------------------------------------------------------|
; sim card configuration
;--------------------------------------------------------------------------------
[smc_para]
smc_used = 0
smc_rst = port:PH13<5><default><default><default>
smc_vppen = port:PH14<5><default><default><default>
smc_vppp = port:PH15<5><default><default><default>
smc_det = port:PH16<5><default><default><default>
smc_vccen = port:PH17<5><default><default><default>
smc_sck = port:PH18<5><default><default><default>
smc_sda = port:PH19<5><default><default><default>
;------------------------------------------------------------------------------------------
;ps2 configuration
;------------------------------------------------------------------------------------------
[ps2_0_para]
ps2_used = 0
ps2_scl = port:PI20<2><1><default><default>
ps2_sda = port:PI21<2><1><default><default>
[ps2_1_para]
ps2_used = 0
ps2_scl = port:PI14<3><1><default><default>
ps2_sda = port:PI15<3><1><default><default>
;------------------------------------------------------------------------------------------
;can bus configuration
;------------------------------------------------------------------------------------------
[can_para]
can_used = 0
can_tx = port:PA16<3><default><default><default>
can_rx = port:PA17<3><default><default><default>
;------------------------------------------------------------------------------------------
;key matrix
;------------------------------------------------------------------------------------------
[keypad_para]
kp_used = 0
kp_in_size = 8
kp_out_size = 8
kp_in0 = port:PH08<4><1><default><default>
kp_in1 = port:PH09<4><1><default><default>
kp_in2 = port:PH10<4><1><default><default>
kp_in3 = port:PH11<4><1><default><default>
kp_in4 = port:PH14<4><1><default><default>
kp_in5 = port:PH15<4><1><default><default>
kp_in6 = port:PH16<4><1><default><default>
kp_in7 = port:PH17<4><1><default><default>
kp_out0 = port:PH18<4><1><default><default>
kp_out1 = port:PH19<4><1><default><default>
kp_out2 = port:PH22<4><1><default><default>
kp_out3 = port:PH23<4><1><default><default>
kp_out4 = port:PH24<4><1><default><default>
kp_out5 = port:PH25<4><1><default><default>
kp_out6 = port:PH26<4><1><default><default>
kp_out7 = port:PH27<4><1><default><default>
;--------------------------------
;--- USB0控制标志
;--------------------------------
[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PH4<0><1><default><default>
usb_det_vbus_gpio = port:PH5<0><0><default><default>
usb_drv_vbus_gpio = port:PB9<1><0><default><0>
usb_host_init_state = 0
;--------------------------------
;--- USB1控制标志
;--------------------------------
[usbc1]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_id_gpio =
usb_det_vbus_gpio =
usb_drv_vbus_gpio = port:PH6<1><0><default><0>
usb_host_init_state = 1
;--------------------------------
;--- USB2控制标志
;--------------------------------
[usbc2]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_id_gpio =
usb_det_vbus_gpio =
usb_drv_vbus_gpio = port:PH3<1><0><default><0>
usb_host_init_state = 0
;--------------------------------
;--- USB Device
;--------------------------------
[usb_feature]
vendor_id = 0x18D1
mass_storage_id = 0x0001
adb_id = 0x0002
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"
[msc_feature]
vendor_name =USB 2.0
product_name =USB Flash Driver
release = 100
luns = 2
;--------------------------------------------------------------------------------
; G sensor configuration
; gs_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2)
;--------------------------------------------------------------------------------
[gsensor_para]
gsensor_used =1
gsensor_name = "bma250"
gsensor_twi_addr =0x18
;gsensor_name = "bma222"
;gsensor_twi_addr =0x08
;gsensor_name = "mma7660"
;gsensor_twi_addr =0x4C
gsensor_twi_id = 1
gsensor_int1 = port:PH00<6><1><default><default>
gsensor_int2 = port:PI10<6><1><default><default>
;--------------------------------------------------------------------------------
; gps gpio configuration
; gps_spi_id --- the index of SPI controller. 0: SPI0, 1: SPI1, 2: SPI2, 15: no SPI used
; gps_spi_cs_num --- the chip select number of SPI controller. 0: SPI CS0, 1: SPI CS1
; gps_lradc --- the lradc number for GPS used. 0 and 1 is valid, set 2 if not use lradc
;--------------------------------------------------------------------------------
[gps_para]
gps_used = 0
gps_spi_id = 2
gps_spi_cs_num = 0
gps_lradc = 1
gps_clk = port:PI00<2><default><default><default>
gps_sign = port:PI01<2><default><default><default>
gps_mag = port:PI02<2><default><default><default>
gps_vcc_en = port:PC22<1><default><default><0>
gps_osc_en = port:PI14<1><default><default><0>
gps_rx_en = port:PI15<1><default><default><0>
;--------------------------------------------------------------------------------
;sdio wifi configuration
;wifi_sdc_id --- 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3
;sdio_wifi_mod_sel --- 0- none, 1- swl-n20(wifi), 2- usi bm-01(wifi+bt+fm),
; 3- ar6302qfn,4- apm6xxx, 5- swb b23(wifi+bt+fm)
; 6- hw-mw269x(v1/v2)
;--------------------------------------------------------------------------------
[sdio_wifi_para]
sdio_wifi_used =1
sdio_wifi_sdc_id = 3
sdio_wifi_mod_sel = 8
;8 GB9663 (bcm40183)
bcm40183_pwr = port:PH12<1><default><default><0>
bcm40183_wl_regon = port:PH11<1><default><default><0>
bcm40183_bt_rst = port:PH10<1><default><default><0>
bcm40183_bt_regon = port:PH14<1><default><default><0>
; 1 - samsung swl-n20 sdio wifi gpio config
;swl_n20_shdn = port:PH09<1><default><default><0>
;swl_n20_host_wakeup = port:PH10<1><default><default><1>
;swl_n20_vdd_en = port:PH11<1><default><default><0>
;swl_n20_vcc_en = port:PH12<1><default><default><0>
; 2 - usi bm01a sdio wifi gpio config
;usi_bm01a_wl_pwr = port:PH12<1><default><default><0>
;usi_bm01a_wlbt_regon = port:PI11<1><default><default><0>
;usi_bm01a_wl_rst = port:PI10<1><default><default><0>
;usi_bm01a_wl_wake = port:PI12<1><default><default><0>
;usi_bm01a_bt_rst = port:PB05<1><default><default><0>
;usi_bm01a_bt_wake = port:PI20<1><default><default><0>
;usi_bm01a_bt_hostwake = port:PI21<0><default><default><0>
; 3 - ar6302qfn sdio wifi gpio config
;ar6302_qfn_pwr = port:PH12<1><default><default><0>
;ar6302_qfn_shdn_n = port:PH09<1><default><default><0>
; 4 - apm sdio wifi gpio config
;apm_6981_vcc_en = port:PA09<1><default><default><0>
;apm_6981_vdd_en = port:PA10<1><default><default><0>
;apm_6981_wakeup = port:PA11<1><default><default><0>
;apm_6981_rst_n = port:PA12<1><default><default><0>
;apm_6981_pwd_n = port:PA13<1><default><default><0>
; 6 - huawei mw269x(v1/v2) sdio wifi gpio config
;hw_mw269x_wl_pwr = port:PH12<1><default><default><0>
;hw_mw269x_wl_enb = port:PH11<1><default><default><0>
;hw_mw269x_wl_hostwake = port:PH10<0><default><default><0>
;hw_mw269x_wl_wake = port:PH09<1><default><default><0>
;hw_mw269x_bt_enb = port:PB05<1><default><default><0>
;hw_mw269x_bt_wake = port:PI20<1><default><default><0>
;hw_mw269x_bt_hostwake = port:PI21<0><default><default><0>
;--------------------------------------------------------------------------------
;usb wifi configuration
;usb_wifi_id --- 0- USB0, 1- USB1, 2- USB2
;--------------------------------------------------------------------------------
[usb_wifi_para]
usb_wifi_used =0
usb_wifi_usbc_num = 2
;--------------------------------------------------------------------------------
;3G configuration
;--------------------------------------------------------------------------------
[3g_para]
3g_used = 1
3g_usbc_num = 1
3g_usbc_type = 2
3g_uart_num = 0
3g_vbat_gpio = port:PA2<1><0><default><0>
3g_power_on_off_gpio = port:PA1<1><0><default><1>
3g_reset_gpio = port:PA0<1><0><default><0>
3g_wakeup_in_gpio = port:PA3<1><0><default><0>
3g_wakeup_out_gpio = port:PH2<1><0><default><0>
[hp_para]
hp_used = 1
hp_det = port:PI10<0><1><default><default>
smc_det = port:PA4<0><1><default><default>
3g_rst = port:PI12<1><default><default><0>
d_ctl = port:PH15<1><default><default><0>
;--------------------------------------------------------------------------------
;gyroscope
;--------------------------------------------------------------------------------
[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 0x00
gy_int1 = port:PH18<6><1><default><default>
gy_int2 = port:PH19<6><1><default><default>
;--------------------------------------------------------------------------------
;light sensor
;--------------------------------------------------------------------------------
[ls_para]
ls_used = 0
ls_twi_id = 1
ls_twi_addr = 0x00
ls_int = port:PH20<6><1><default><default>
;--------------------------------------------------------------------------------
;compass
;--------------------------------------------------------------------------------
[compass_para]
compass_used = 0
compass_twi_id = 1
compass_twi_addr = 0x00
compass_int = port:PI13<6><1><default><default>
;--------------------------------------------------------------------------------
;blue tooth
;bt_used ---- blue tooth used (0- no used, 1- used)
;bt_uard_id ---- uart index
;bt_mod_type ---- 0-none, 1-bcm bt
;--------------------------------------------------------------------------------
[bt_para]
bt_used = 0
bt_uart_id = 2
bt_mod_type = 1
[i2s_para]
i2s_used = 0
i2s_channel = 2
i2s_mclk = port:PB5<2><1><default><default>
i2s_bclk = port:PB6<2><1><default><default>
i2s_lrclk = port:PB7<2><1><default><default>
i2s_dout0 = port:PB8<2><1><default><default>
i2s_dout1 =
i2s_dout2 =
i2s_dout3 =
i2s_din = port:PB12<2><1><default><default>
[spdif_para]
spdif_used = 0
spdif_mclk =
spdif_dout = port:PB13<4><1><default><default>
spdif_din =
[audio_para]
audio_used = 1
audio_pa_ctrl = port:PH15<1><default><default><0>
audio_earphone_ctrl = port:PI11<1><default><default><0>
;----------------------------------------------------------------------------------
;ir --- infra remote configuration
;----------------------------------------------------------------------------------
[ir_para]
ir_used = 1
ir0_rx = port:PB04<2><default><default><default>
;----------------------------------------------------------------------------------
;pmu_twi_addr ---slave address
;pmu_twi_id ---i2c bus number (0 TWI0, 1 TWI2, 2 TWI3)
;pmu_irq_id ---irq number (0 irq0,1 irq1,……)
;pmu_battery_rdc ---battery initial resistance,mΩ,根据实际电池内阻填写
;pmu_battery_cap ---battery capability,mAh，根据实际电池容量填写
;pmu_init_chgcur ---set initial charging current limite,mA，300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800
;pmu_suspend_chgcur ---set suspend charging current limite,mA，300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800
;pmu_resume_chgcur ---set resume charging current limite,mA，300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800
;pmu_shutdown_chgcur ---set shutdown charging current limite,mA，300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800
;pmu_init_chgvol ---set initial charing target voltage,mV,4100/4150/4200/4360
;pmu_init_chgend_rate ---set initial charing end current rate,10/15
;pmu_init_chg_enabled ---set initial charing enabled,0:关闭,1:打开
;pmu_init_adc_freq ---set initial adc frequency,Hz,25/50/100/200
;pmu_init_adc_freqc ---set initial coulomb adc coufrequency,Hz,25/50/100/200
;pmu_init_chg_pretime ---set initial pre-charging time,min,40/50/60/70
;pmu_init_chg_csttime ---set initial constance-charging time,min,360/480/600/720
;pmu_usbvol_limit ---set usb voltage limited enable,0:关闭,1:打开
;pmu_usbvol ---set usb limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700
;pmu_usbcur_limit ---set usb current limited enable,0:关闭,1:打开
;pmu_usbcur ---set usb limited voltage level,mA,100/500/900
;pmu_pwroff_vol ---set protect voltage when system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pwron_vol ---set protect voltage after system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pekoff_time ---set pek off time,ms, 4000/6000/8000/10000
;pmu_pekoff_en ---set pek off enable, 0:关闭,1:打开
;pmu_peklong_time ---set pek pek long irq time,ms,1000/1500/2000/2500
;pmu_pekon_time ---set pek on time,ms,128/1000/2000/3000
;pmu_pwrok_time ---set pmu pwrok delay time,ms,8/64
;pmu_pwrnoe_time ---set pmu n_oe power down delay time,ms,128/1000/2000/3000
;pmu_intotp_en ---set pmu power down when overtempertur enable,0:关闭，1：打开
;----------------------------------------------------------------------------------
[pmu_para]
pmu_used = 1
pmu_twi_addr = 0x34
pmu_twi_id = 0
pmu_irq_id = 0
pmu_battery_rdc = 150
pmu_battery_cap = 2600
;pmu_init_chgcur = 300
pmu_init_chgcur = 600
pmu_earlysuspend_chgcur = 600
pmu_suspend_chgcur = 1000
pmu_resume_chgcur = 300
pmu_shutdown_chgcur = 1000
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 200
pmu_init_adc_freqc = 100
pmu_init_chg_pretime = 50
pmu_init_chg_csttime = 720
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 2
pmu_bat_para6 = 8
pmu_bat_para7 = 16
pmu_bat_para8 = 22
pmu_bat_para9 = 33
pmu_bat_para10 = 43
pmu_bat_para11 = 50
pmu_bat_para12 = 59
pmu_bat_para13 = 71
pmu_bat_para14 = 83
pmu_bat_para15 = 92
pmu_bat_para16 = 100
pmu_usbvol_limit = 1
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 500
pmu_usbvol_pc = 4000
pmu_usbcur_pc = 0
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2900
pmu_pekoff_time = 9000
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_pwrnoe_time = 2000
pmu_intotp_en = 1
pmu_used2 = 0
pmu_adpdet = port:PH02<0><default><default><default>
pmu_init_chgcur2 = 400
pmu_earlysuspend_chgcur2 = 600
pmu_suspend_chgcur2 = 1200
pmu_resume_chgcur2 = 400
pmu_shutdown_chgcur2 = 1200
;lowe power warning/shutdown voltage
pmu_suspendpwroff_vol = 3500
pmu_batdeten = 0
; Vol- = 18
; Vol+ = 24
[recovery_key]
key_min =4
key_max =100
|
[复制链接]
发表于 2012-11-17 15:50:18
楼主