本帖最后由 恋爱的夏娜 于 2013-4-12 17:40 编辑
Error Message:
KERNEL_DATA_INPAGE_ERROR
Explanation:
This Stop message indicates that the requested page of kernel data from the paging file could not be read into memory. This Stop message is usually caused by a bad block (sector) in a paging file, a virus, a disk controller error, or failing RAM. In rare cases, it is caused when nonpaged pool resources run out. It is also caused by defective hardware.
User Action:
If the I/O status is C0000185 and the paging file is on a SCSI disk, the disk cabling and SCSI termination should be checked for problems. Check your computer for viruses, using any up-to-date, commercial virus scanning software that examines the Master Boot Record of the hard disk. An I/O status code of 0xC000009C or 0xC000016A normally indicates the data cannot be read from the disk due to a bad block (sector). If you can restart the system after the error, Autochk runs automatically and attempts to map out the bad sector. If Autochk does not scan the hard disk for errors, manually launch the disk scanner. Run Chkdsk /f /r on the system partition. Restart the system before the disk scan begins. If you cannot start the system due to the error, use the Recovery Console and run Chkdsk /r. Caution: If your system partition is formatted with the FAT file system, the long file names used by Windows 2000 can be damaged if Scandisk or another MS-DOSbased hard disk tool is used to verify the integrity of your hard disk from an MS-DOS prompt. (An MS-DOS prompt is typically derived from an MS-DOS startup disk or from starting MS-DOS on a multiboot system.) Always use the Windows 2000 version of Chkdsk on Windows 2000 disks. Another common cause of this Stop message is failing RAM. Run hardware diagnostics supplied by the system manufacturer, especially the memory scanner. For details on these procedures, see the owners manual for your computer. Check that all network adapters in the computer are properly seated. Use an ink eraser or an electrical contact treatment, available at electronics supply stores, to ensure network adapter contacts are clean. Check the System Log in Event Viewer for additional error messages that might help pinpoint the device causing the error. Disabling memory caching of the BIOS might also resolve it. Finally, if all the above steps fail to resolve the error, take the system motherboard to a repair facility for diagnostic testing. A crack, a scratched trace, or a defective component on the motherboard can also cause this error. For more troubleshooting information about this Stop message, refer to the Microsoft Knowledge Base at http://support.microsoft.com/support.
错误信息：
KERNEL_DATA_INPAGE_ERROR
错误代码解释：
这个错误代码的出现表明从页面文件的核心数据区所请求的页不能从内存中读取。这个错误信息的产生一般是因为页面文件里的一个坏扇区/坏块，病毒，一个磁盘控制器错误，或者出错的RAM。在很罕见的情况下，当未分页池的资源耗尽的时候也会出现这个错误。他也可能由硬件缺陷产生。
用户可采取的行动：
如果返回的IO状态代码为C0000185且页面文件在一个SCSI磁盘上，磁盘的线缆连接和SCSI的终止状态（？）需要重点检查以排除问题。检查你的电脑上有无病毒，使用任意最新的商业反病毒软件扫描硬盘的主引导扇区MBR。当IO状态代码为0xC000009C或者0xC000016A时，一般意味着因为磁盘上的坏扇区/坏块而导致数据无法被读取。如果你可以在此错误以后重启系统，Autochk程序会自动运行并尝试映射掉所有的坏扇区（也就是所谓的坏扇区修复）。如果Autochk没有进行硬盘查错，手动启动磁盘扫描工具。在系统分区运行 Chkdsk /f /r 。在磁盘扫描开始之前重启系统。如果你因为这个（磁盘）错误无法重启系统的话，使用故障恢复控制台（官方就一个Recovery Console！）运行Chkdsk /r 。警告：如果你的系统分区被格式化成FAT格式分区，且使用Scandisk或者其他基于MS-DOS的硬盘工具在MS-DOS命令提示符下校验你的硬盘文件的完整性的话，被Windows 2000系统使用的长文件名文件的文件名会被破坏。（一个MSDOS提示符通常由一块MSDOS启动盘引导获得或者通过多重引导系统的MSDOS系统引导获得）始终在安装/运行Windows 2000的磁盘上运行Windows 2000版本的chkdsk工具。另一种可能引发此错误的原因是因为失败的内存（读写？）。运行你的系统制造商发布的硬件诊断工具，尤其是内存扫描工具。要获得如何使用这类型工具的详细信息及其他相关信息，请查阅你的电脑的用户手册。检查电脑上安装的所有网络适配器都正确安装了（比如NIC的插槽有没有插牢）。用一个在五金店或者电工商店都有的橡皮擦（？）或者一个电力接口维护工具（？）来处理，确保网线接口和网线插口是干净的。（其实就是类似于擦拭内存金手指一样的东西啦！！）。在系统的事件查看器里面检查系统日志来获得更多的有助于定位引发错误的设备的错误消息。在BIOS里面禁用Memory Caching也可能解决这个问题。最后，如果上述所有步骤都无法解决问题，拿着主板去维修机构寻求硬件检测。一个被破坏（破解？）的，a scratched trace（实在不懂了！！），或者主板上一个存在缺陷的组件也会引起这个错误。更多的和这个错误消息相关的疑难解答消息可以访问http://support.microsoft.com/support 上的微软知识库。
太难翻译了！！！ |
[复制链接]
发表于 2013-4-12 16:41:19
楼主
算了，我自己翻译吧。。。
我去翻译我去翻译~~~~